目次

1. MACHADO, A.R. and WALLBANK, J., "Machining of Titanium and Its Alloys ‑ A Review".- 2. EZUGWU, E.O.; MACHADO,A.R.; PASHBY, I.R. and WALLBANK, J. ‑ "Effects of High Pressure Coolant Supply when Machining Heat Resistant Nickel Based Superalloys".- 3. EZUGWU, E.O.; WANG, Z.M.; MACHADO, A.R., “The Machinability of Nickel Based Alloys – A Review”.- 4. MACHADO, A.R.; WALLBANK, J.; PASHBY, I.R. and EZUGWU, E.O., “Tool Performance and Chip Control when Machining Titanium (Ti6Al4V) and Nickel (Inconel 901) Base Superalloy Using High Pressure Coolant Supply”.- 5. EZUGWU, E.O.; WANG, Z.M.; MACHADO, A.R., “Wear of Coated Carbide Tools when Machining Nickel (Inconel 718) and Titanium Base (Ti-6Al-4V) Alloys”.- 6. EZUGWU, E.O.; Da SILVA, R.B.; MACHADO, A.R., “Evaluation of the performance of Different Nano-Ceramic Tool Grades when Machining Nickel-Base, Inconel 718 Alloy”.- 7. EZUGWU, E.O.; Da SILVA, R.B.; BONNEY, J.; MACHADO, A.R., “The Effect of Argon-Enriched Environment in High-Speed Machining of Titanium Alloy”.- 8. EZUGWU, E.O.; Da SILVA, R.B.; BONNEY, J.; MACHADO, A.R., “Evaluation of the Performance of cBN Tools when Turning Ti-6Al-4V Alloy with High Pressure Coolant Supplies”.- 9. Da SILVA, R.B.; MACHADO, A.R.; EZUGWU, E.O.; BONNIE,J., “Increasing Productivity in High Speed Machining of Ti-6Al-4V Alloy under High Pressure Coolant Supply”.- 10. Da SILVA, R.B.; EZUGWU, E.O.; BONNEY, J.; MACHADO, A.R.; REIS, A.M., “High Speed Turning of Ti-6Al-4V Alloy with coated Carbides Tools in an Argon Enriched Enviroment”.- 11. EZUGWU, E.O.; BONNEY, J.; Da SILVA, R.B.; MACHADO, A.R.; UGWOHA, E., “High Productivity Rough Turning of Ti6Al4V Alloy, with Flood and High Pressure Cooling”.- 12. Da SILVA, R.B.; MACHADO, A.R.; EZUGWU, E.O., BONNEY, J.; SALES, W.F., “Tool life and Wear Mechanisms in High Speed Machining of Ti-6Al-4V Alloy with PCD Tools under Various Coolant Pressures”.- 13. MOURA, R.R.; Da SILVA, M.B.; MACHADO, A.R.; SALES, W.F., “The Effect of Application of Cutting Fluid with Solid Lubricant in Suspension During Cutting of Ti-6Al-4V Alloy”.- 14. MARQUES, A.; NARALA, S.K.R.; MACHADO, A.R.; GUNDA, R.K.; JOSYULA, S.K.; Da SILVA, R.B.; Da SILVA, M.B., “Performance Assessment of MQSL: Minimum Quantity Solid Lubricant During Turning of Inconel 718”.- 15. Da SILVA, R.B.; Da SILVA, M.B.; SALES, W.F.; EZUGWU, E.O.; MACHADO, A.R. “Advances in the Turning of Titanium Alloys with Carbide and Superabrasive Cutting Tools”.